Logmanoriginal: Remove redlinks for individual error code pages.

2023-05-07T15:45:52Z

Remove redlinks for individual error code pages.

Q: Added page

2021-09-20T02:49:47Z

Added page

New page

Below are all of the Error Codes that belong to the '''LabVIEW WSN''' Error Code Family (see [[Error List]] for list of Families).

{| class="wikitable sortable"
! Code
! Description
|-
| [[Error Code -25399|-25399]]
| LabVIEW WSN: (Hex 0xFFFF9CC9) The last LV WSN Error. Turn back, padawan, there is no where else to go.
|-
| [[Error Code -25339|-25339]]
| LabVIEW WSN: (Hex 0xFFFF9D05) You must enable the serial port receiver power before calling this function, or no new data can be read.
|-
| [[Error Code -25338|-25338]]
| LabVIEW WSN: (Hex 0xFFFF9D06) The device does not support reading or writing the specified number of bytes from the serial port at one time.
|-
| [[Error Code -25337|-25337]]
| LabVIEW WSN: (Hex 0xFFFF9D07) The specified number of bytes cannot be read or written within the specified timeout.
|-
| [[Error Code -25336|-25336]]
| LabVIEW WSN: (Hex 0xFFFF9D08) The specified serial port configuration is unsupported on this device.
|-
| [[Error Code -25327|-25327]]
| LabVIEW WSN: (Hex 0xFFFF9D11) Not enough user RAM.
|-
| [[Error Code -25326|-25326]]
| LabVIEW WSN: (Hex 0xFFFF9D12) Invalid user RAM refnum.
|-
| [[Error Code -25325|-25325]]
| LabVIEW WSN: (Hex 0xFFFF9D13) Verification of user memory failed.
|-
| [[Error Code -25324|-25324]]
| LabVIEW WSN: (Hex 0xFFFF9D14) Failed to write to user memory.
|-
| [[Error Code -25323|-25323]]
| LabVIEW WSN: (Hex 0xFFFF9D15) Failed to write to user memory because the location is not empty.
|-
| [[Error Code -25322|-25322]]
| LabVIEW WSN: (Hex 0xFFFF9D16) User memory out of bounds. The operation specified a location outside the user memory sector.
|-
| [[Error Code -25321|-25321]]
| LabVIEW WSN: (Hex 0xFFFF9D17) Failed to erase the specified user memory sector.
|-
| [[Error Code -25320|-25320]]
| LabVIEW WSN: (Hex 0xFFFF9D18) Null pointer exception.
|-
| [[Error Code -25313|-25313]]
| LabVIEW WSN: (Hex 0xFFFF9D1F) Internal error: Hardware failure.
|-
| [[Error Code -25312|-25312]]
| LabVIEW WSN: (Hex 0xFFFF9D20) The node is not connected.
|-
| [[Error Code -25311|-25311]]
| LabVIEW WSN: (Hex 0xFFFF9D21) Invalid argument.
|-
| [[Error Code -25310|-25310]]
| LabVIEW WSN: (Hex 0xFFFF9D22) User message missed.
|-
| [[Error Code -25309|-25309]]
| LabVIEW WSN: (Hex 0xFFFF9D23) Radio failure: An internal error has occurred. Please contact National Instruments technical support at ni.com/support.
|-
| [[Error Code -25308|-25308]]
| LabVIEW WSN: (Hex 0xFFFF9D24) Flash failure: An internal error has occurred. Please contact National Instruments technical support at ni.com/support.
|-
| [[Error Code -25307|-25307]]
| LabVIEW WSN: (Hex 0xFFFF9D25) Command queue overflow: An internal error has occurred. Please contact National Instruments technical support at ni.com/support.
|-
| [[Error Code -25306|-25306]]
| LabVIEW WSN: (Hex 0xFFFF9D26) Digital output line failure: An internal error has occurred. Please contact National Instruments technical support at ni.com/support.
|-
| [[Error Code -25305|-25305]]
| LabVIEW WSN: (Hex 0xFFFF9D27) ADC failure: An internal error has occurred. Please contact National Instruments technical support at ni.com/support.
|-
| [[Error Code -25304|-25304]]
| LabVIEW WSN: (Hex 0xFFFF9D28) CJC failure: An internal error has occurred. Please contact National Instruments technical support at ni.com/support.
|-
| [[Error Code -25303|-25303]]
| LabVIEW WSN: (Hex 0xFFFF9D29) SPI communication failure: An internal error has occurred. Please contact National Instruments technical support at ni.com/support.
|-
| [[Error Code -25302|-25302]]
| LabVIEW WSN: (Hex 0xFFFF9D2A) Serial receiving failure: An internal error has occurred. Please contact National Instruments technical support at ni.com/support.
|-
| [[Error Code -25301|-25301]]
| LabVIEW WSN: (Hex 0xFFFF9D2B) Serial transmission failure: An internal error has occurred. Please contact National Instruments technical support at ni.com/support.
|-
| [[Error Code -25300|-25300]]
| LabVIEW WSN: (Hex 0xFFFF9D2C) An internal error has occurred in the LabVIEW Wireless Sensor Network Module. Please contact National Instruments technical support at ni.com/support.
|-
| [[Error Code -25283|-25283]]
| LabVIEW WSN: (Hex 0xFFFF9D3D) The node ID does not exist in the gateway's node table.
|-
| [[Error Code -25282|-25282]]
| LabVIEW WSN: (Hex 0xFFFF9D3E) Invalid message reference.
|-
| [[Error Code -25281|-25281]]
| LabVIEW WSN: (Hex 0xFFFF9D3F) Invalid node reference.
|-
| [[Error Code -25280|-25280]]
| LabVIEW WSN: (Hex 0xFFFF9D40) Invalid gateway reference.
|-
| [[Error Code -25254|-25254]]
| LabVIEW WSN: (Hex 0xFFFF9D5A) Connection timed out. Gateway might be in a bad state.
|-
| [[Error Code -25253|-25253]]
| LabVIEW WSN: (Hex 0xFFFF9D5B) Double interface registration: An internal error has occurred. Please contact National Instruments technical support at ni.com/support.
|-
| [[Error Code -25252|-25252]]
| LabVIEW WSN: (Hex 0xFFFF9D5C) Incompatible or corrupted data was received from the gateway.
|-
| [[Error Code -25251|-25251]]
| LabVIEW WSN: (Hex 0xFFFF9D5D) Memory error. Unable to deallocate used memory.
|-
| [[Error Code -25250|-25250]]
| LabVIEW WSN: (Hex 0xFFFF9D5E) Memory allocation failed.
|-
| [[Error Code -25230|-25230]]
| LabVIEW WSN: (Hex 0xFFFF9D72) The request processor failed to deserialize a request. This error can occur if protocol versions are incompatible or data is corrupt.
|-
| [[Error Code -25229|-25229]]
| LabVIEW WSN: (Hex 0xFFFF9D73) The request processor failed to deserialize a request. This error can occur if protocol versions are incompatible.
|-
| [[Error Code -25228|-25228]]
| LabVIEW WSN: (Hex 0xFFFF9D74) The request terminated due to an unhandled exception.
|-
| [[Error Code -25227|-25227]]
| LabVIEW WSN: (Hex 0xFFFF9D75) Memory allocation failed.
|-
| [[Error Code -25226|-25226]]
| LabVIEW WSN: (Hex 0xFFFF9D76) The client was denied access.
|-
| [[Error Code -25225|-25225]]
| LabVIEW WSN: (Hex 0xFFFF9D77) The client aborted the connection.
|-
| [[Error Code -25224|-25224]]
| LabVIEW WSN: (Hex 0xFFFF9D78) Network communication failed.
|-
| [[Error Code -25223|-25223]]
| LabVIEW WSN: (Hex 0xFFFF9D79) Connection timed out.
|-
| [[Error Code -25222|-25222]]
| LabVIEW WSN: (Hex 0xFFFF9D7A) Unable to connect to the named service.
|-
| [[Error Code -25221|-25221]]
| LabVIEW WSN: (Hex 0xFFFF9D7B) Unable to connect to the named gateway.
|-
| [[Error Code -25220|-25220]]
| LabVIEW WSN: (Hex 0xFFFF9D7C) Generic connection error.
|-
| [[Error Code -25200|-25200]]
| LabVIEW WSN: (Hex 0xFFFF9D90) First LV WSN Error
|-
| [[Error Code 21100|21100]]
| LabVIEW WSN: (Hex 0x526C) First LV WSN Warning
|-
| [[Error Code 21240|21240]]
| LabVIEW WSN: (Hex 0x52F8) The serial port receiver received a break condition on the line.
|-
| [[Error Code 21241|21241]]
| LabVIEW WSN: (Hex 0x52F9) The specified number of bytes were read from the serial port before the specified termination string was detected.
|-
| [[Error Code 21299|21299]]
| LabVIEW WSN: (Hex 0x5333) The last LV WSN Warning.
|}

[[Category:Error Handling]]

LabVIEW WSN Error Code Family - Revision history

Logmanoriginal: Remove redlinks for individual error code pages.

Q: Added page